Machines · equipment
Accessories & seeding equipment. From one modular system.
Pneumatic seeders and front tank, metering rollers, points for the Super Maxx® and front implements for rollers and cultivators – what fits which GÜTTLER machine.
- Pneumatic seeder
- Front tank
- Metering rollers
- Points
- Front implements
Seeding equipment
EPS 5 pneumatic seeder. Up to 670 litres.
Sow where the machine is going anyway: the pneumatic seeder fits on the GreenMaster, Super Maxx®, OffSet® and MATADOR – BROADCAST SEEDING or TINE SEED.
Seed drill or seeding equipment?
GÜTTLER’s cultivator drill is the Super Maxx® CultiSem: soil cultivation and sowing in a single pass. For overseeding grassland, the GreenMaster TINE SEED places the seed via seed tubes at the harrow tines just 3 cm above the ground. The MAYOR with mounted seed tank sows catch crops and undersown crops. And on the GreenMaster, Super Maxx®, OffSet® and MATADOR, the EPS 5 pneumatic seeder does the sowing – more on this below.
Super Maxx® CultiSemGreenMaster TINE SEEDMAYOR with seed tank
- Seed tank up to 670 litres
- Easy calibration, finely graduated seed rate adjustment
- Electric or hydraulic fan
- Several control units: Standard, SeedProfi Basic or High
Accessories for pneumatic seeders
- Hectare counter (daily and total counter)
- Electric seed rate adjustment from the tractor
- TL 17 tank/airflow monitoring
- Tank monitoring and seed rate adjustment
- Hydraulic lifting for the ground drive wheel
- Cover for 200 / 410 / 640–660 litres
- Conversion from electric to hydraulic fan
| Tank | Fan | Version | Control | Fits on |
|---|---|---|---|---|
| 200l | electric (SI) | – | Standard · SeedProfi Basic | GreenMaster 250 / 300 |
| 410l | electric (SI), 90° | – | Standard · Basic · High | GreenMaster 250 / 300, 600, EcoLine |
| 410l | hydraulic, 90° | – | Standard · Basic · High | GreenMaster, Super Maxx® BIO and CULTI, OffSet®, MATADOR (Alpin) |
| 640l | hydraulic | BROADCAST SEEDING | Standard · Basic · High | GreenMaster 600 / 750 / 800 |
| 660l | hydraulic | BROADCAST SEEDING | Standard · Basic · High | GreenMaster Alpin (MATADOR 610 / 760) |
| 640l | hydraulic, reinforced | TINE SEED | Basic · High | GreenMaster 600 TINE SEED |
| 670l | hydraulic, reinforced | TINE SEED | Basic · High | GreenMaster 800 TINE SEED |
Hydraulic fan: 1 × SA with pressure-free return, oil flow 15–20 litres per minute. Mounting requires a separate bracket for each machine type (except the folding GreenMaster). Standard: 8R3S metering roller, ground drive with WK4 angle gearbox. Pulse wheel if there is no 7-pin signal socket. SA = single-acting spool valve.
Catch crops & undersowing
MAYOR with seed tank.
With the mounted seed tank, the MAYOR Prismenwalze® (prism roller) is suitable for sowing catch crops and undersown crops. After automatic calibration, you control the seeding equipment conveniently from the cab via the SeedProfi terminal; the seed is spread evenly in front of the Prismenwalze® and pressed in by 305 prism points per square metre.
- Conversion kit also available for existing MAYOR 640 / 770 / 820
- Efficient retrofit for catch crops and overseeding
Front tank
Seed and fertiliser at the front.
With mechanical fan and SeedProfi – carried by an AVANT or DUPLEX®, combined with a Super Maxx® CultiSem or a power harrow drill combination.
| Version | Tank | Metering | Control | Weight |
|---|---|---|---|---|
| EPS 5 front tank | 700l | EPS 5 metering unit, 8R3S metering roller, 1 calibration tray | SeedProfi Basic or High · optional stainless steel tank | 210–215kg |
| EPS 8 front tank | 1,530l | EPS 8 double metering unit in chromium steel, 2 × 8R3S + 2 × 8R2B, 2 calibration trays | with SeedProfi | 470kg |
Supplied as standard with mechanical fan incl. PTO shaft and marker boards with LED lighting. The hose routing is arranged individually on site by the workshop.
Front tank accessories
- Seeding boom 5.00 to 12.00 m, mechanically folding, transport width 2.30 m
- Distributor head for direct seed distribution
- Ø 110 mm hoses and airflow booster
- Fertiliser/seed sieve
- SIMPLEX 56 support roller (2.3 m) to relieve the front axle in the field
- Adapter for AVANT: coupling the front tank in front of the roller
DUPLEX® as carrier
Without a tined unit, the DUPLEX® carries the front tank: when working, the tractor loads the soil with its unladen weight only, the weight of the tank contributes to crumbling and reconsolidation – and axle loads remain balanced when turning and on the road.
Metering rollers
The right metering roller for every type of seed.
For all types of seed at a wide range of working speeds – the calibration tables are available under Downloads.
| Metering roller | Seed size | Applications |
|---|---|---|
| 8R1L | extra fine | very small quantities and small working widths |
| 8R1R | fine | fine seeds in large quantities, e.g. oilseed rape, mustard, clover |
| 8R1S | medium | fine seeds in large quantities or at high speeds |
| 8R3S | coarse · standard | grass and catch crop mixtures |
| 8R2B | extra coarse | very large quantities; hydraulic or mechanical fan recommended |
| 8R1S D | medium | fine seeds in small quantities below 7 kg/ha – included with SeedProfi Basic/High |
For the GreenMaster 800 TINE SEED, the same grades are available as 12R metering rollers (12R1L to 12R1S D). Other metering rollers on request.
Points for Super Maxx®
Seven points.
All for the Super Maxx® 45 × 12 mm tine with double spring – sets sized by working width.
-
Standard
Narrow point
Standard on the 45 × 12 mm tine with double spring; reversible point – simply turn it round when it reaches the wear limit.
-
up to 8 times the service life
36 mm tungsten carbide narrow point
Hard-faced 20 mm tungsten carbide tip with special geometry for improved mixing.
-
New
55 mm tungsten carbide narrow point
Wider 35 mm tungsten carbide tip for more thorough working, fixed to the tine with two bolts; up to 8 times the service life.
-
Mixing
180 mm swept point
Steeper point back for better mixing of the soil.
-
full-width cut
200 mm swept point
For a full-width cut with simultaneous mechanical weed control – 70 mm overlap.
-
up to 2.5 times the service life
Forged point
Extra wear protection for bolt holes and bolt heads; side wings maintain the working width up to the wear limit.
-
New for 2026
Precision point
Beaver-tooth effect: open-pored cut with minimal smearing zones, stepped cutting face; up to 8 times the service life of the 200 mm swept point.
Practical tip
First and second stubble passes with narrow points – crossing diagonally. First break the capillary action and retain germination moisture, then work the soil thoroughly and mix in straw close to the surface, and finally cut shallow and across the full width with the swept point.
| Working width | 3m | 5m | 6m | 7m | 9m | 10m | 12m |
|---|---|---|---|---|---|---|---|
| Tines per set | 22 | 37 | 45 | 55 | 69 | 77 + 6 | 93 + 6 |
Points are supplied as a set per working width; plus 6 track looseners for 10 and 12 m.
Front implements & mounting parts
In front of, behind and next to the roller.
What fits which machine – the configurator shows availability for each type; if in doubt, our sales team will advise you.
-
Cultivator tined unit
150 mm tine spacing, 3-row, complete with side plates and carrier arm – breaks up clods and improves crumbling; fitted to and removed from the DUPLEX® with just three pins.
- AVANT
- DUPLEX®
- MATADOR
-
FlatSpring
Hydraulically adjustable with hydraulic angle adjustment – robust, can be set aggressively, ideal for levelling shallow horizons.
- AVANT
- DUPLEX®
- MATADOR
- OffSet®
- Master
- Super Maxx® 1000 / 1200
- FELDMEISTER®
-
Levelling bar
Parallelogram-guided, height-adjustable, with overload protection – levels molehills and helps to control the corn borer.
- MATADOR
- MAYOR
- MASTERCUT
- GreenMaster
-
Ripperboard QUATTRO
The shortest 4-row harrow: doubles the number of tines to a 37.5 mm tine spacing, removes thatch intensively, levels out unevenness, spreads slurry and manure.
- GreenMaster
- Super Maxx® CULTI · CultiSem
- FELDMEISTER® LK 60
-
NonStop harrow
3-row or 2-row with levelling bar or Ripperboard, optional hydraulic height or angle adjustment.
- Master 940 / 1040
- Magnum 1240
-
Track loosener
On the hitch beam with four tines and quick-change point system with swept point, on the NonStop unit or with double leaf spring on the Super Maxx®.
- MAYOR
- Master · Magnum
- OffSet®
- Super Maxx®
-
Crumbler roller and second harrow row
Crumbler roller instead of a harrow or a second harrow row incl. bracket; levelling board as a retrofit kit.
- Super Maxx® BIO
- Super Maxx® Heavy Duty
-
MEDIANA roller inserts
Shaft with prism rings Ø 33/38 cm in cast iron, semi-synthetic or Synthetic Ultra, 0.98 to 2.05 m – without bearings or frame, for installation.
- MEDIANA
- Conversion kits for vineyard power harrows on request
-
SIMPLEX mounting parts
Conversion kits for all common power harrows; machines not listed are covered by universal basic elements for self-assembly. Please send your enquiry with make, type, year of manufacture and photos.
- Power harrow
- Rotary cultivator
Electronic control
SeedProfi.
The electronic control unit for the pneumatic seeders and the front tank: adjust the seed rate on the move, automatic calibration, fill level and area at a glance.
Advice
Will it fit my machine?
The head office in Kirchheim/Teck will put you in touch with the GÜTTLER sales representative for your region – mounting parts for SIMPLEX directly via anbauteile@guettler.de.
- Head office+49 7021 9857-0
- Emailinfo@guettler.de
AvailableMon–Fri 08:00–17:00 (German time)